Campbell CR5000 Specifiche Pagina 171
- Pagina / 238
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Section 7. Measurement Instructions
7-45
Parameter
& Data Type
Enter
StartChan
Constant
The first channel that should be read on the SW8A. If the Reps parameter is
greater than 1, measurements will be made on sequential channels.
Mult, Offset
Constant,
Variable,
Array, or
Expression
A multiplier and offset by which to scale the raw results of the measurement. See the
measurement description for the units of the raw result; a multiplier of one and an
offset of 0 are necessary to output in the raw units. For example, the
TCDiff
instruction measures a thermocouple and outputs temperature in degrees C. A
multiplier of 1.8 and an offset of 32 will convert the temperature to degrees F.
- CR5000 Measurement and 1
- Control System 1
- Warranty and Assistance 2
- TABLE OF CONTENTS 3
- APPENDIX 4
- CR5000 MICROLOGGER 6
- OV2.1 Memory 9
- OV2.3 Data Tables 10
- OV3.2 PC9000 Installation 10
- OV3.3.1 File 13
- OV3.3.2 Edit 13
- OV4. Keyboard Display 15
- OV4.1 Data Display 16
- OV4.1.1 Real Time Tables 17
- CR5000 Overview 18
- OV4.2 Run/Stop Program 20
- OV4.3 File Display 21
- OV4.3.1 File: Edit 22
- OV4.4 Configure Display 23
- OV5. Specifications 24
- 1.2 Power Requirements 25
- 1.3 CR5000 Power Supplies 26
- 1.4 Solar Panels 28
- BOOST REGULATOR 29
- 1.7 CR5000 GROUNDING 30
- CR5000 ICROLOGGER 31
- 1.10 Maintenance 36
- BATTERY2 38
- (datalogger/cr5000) 38
- 2.1 Data Storage in CR5000 41
- 2.2 Internal Data Format 42
- 2.3 Data Collection 43
- 2.3.1.1 File Type 44
- 2.3.1.2 Collection Method 44
- 2.3.1.3 Table Selection 45
- 2.3.1.4 File Control 45
- 2.3.2 RealTime Write File 46
- 2.3.3 Logger Files Retrieve 47
- 2.3.4 Via PCMCIA PC Card 47
- 2.4 Data Format on Computer 50
- 2.4.2 TOA5 ASCII File Format 51
- 3.1.1 Voltage Range 55
- 3.1.4 SettlingTime 57
- 3.1.5 Integration 57
- Measurements 58
- 3.3 Signal Settling Time 59
- 3.4.1 Error Analysis 62
- Thermocouple Limits of Error 65
- Noise on Voltage Measurement 67
- Error Summary 69
- CR5000 Junction Box 70
- 3.7 Pulse Count Measurements 74
- 3.8 Self Calibration 75
- 4.1 Format Introduction 77
- 4.2 Programming Sequence 78
- 4.3 Example Program 80
- CallTable Temp 82
- 4.4 Numerical Entries 83
- 4.6 Flags 84
- 4.7 Parameter Types 85
- 'Calibration factors: 86
- Station Name 91
- Sub, Exit Sub, End Sub 91
- Subroutine Example 93
- 6.1 Data Table Declaration 95
- 6.2 Trigger Modifiers 96
- OpenInterval 97
- FillStop 99
- 6.3 Export Data Instructions 102
- TableOption 103
- BufferControl 103
- Highlimit, MinAmp, Form) 118
- Code Form 119
- Constant 119
- Measured raw data: 123
- 7.8 Digital I/O 128
- 7.9 Peripheral Devices 128
- 7.1 Voltage Measurements 129
- Integ, Mult, Offset) 130
- 7.3 Half Bridges 131
- 7.4 Full Bridges 134
- 7.5 Current Excitation 137
- 7.7 Self Measurements 141
- Calibrate (Dest, AllRanges) 142
- ± 10 mV) and resolution 146
- Silicon diodes 146
- . Resistor 146
- PortGet (Dest, Port) 147
- PortSet (Port, State) 148
- Pulse Channel 149
- PulseCountReset 151
- ReadIO (Dest, Mask) 151
- TimerIO 153
- WriteIO (Mask, Source) 154
- SDMAddress 156
- SEG TSEG q22 158
- Parameter 160
- & Data Type 160
- Description 165
- Result 167
- SDMSpeed (BitPeriod) 168
- SDMTrigger 168
- ValuesPerRep 170
- This is a blank page 172
- Instructions 173
- ACOS (Source) 174
- ASIN (Source) 175
- ATN (Source) 176
- AvgSpa (Dest, Swath, Source) 177
- Cos (Source) 179
- CosH (Source) 179
- Variable or 180
- Frac (Source) 183
- Int, Fix 186
- Log (Source) 187
- LOG10 (number) 187
- MemoryTest 188
- MaxSpa (Dest, Swath, Source) 188
- MinSpa (Dest, Swath, Source) 189
- Move (Dest, Swath, Source) 190
- Randomize 194
- RealTime 195
- RectPolar (Dest, Source) 196
- RMSSpa (Dest, Swath, Source) 197
- RND (Source) 197
- Sgn (Source) 201
- Sin (Source) 201
- SinH (Source) 202
- Sqr (Source) 202
- StdDevSpa 203
- Tan (Source) 203
- TANH (Source) 204
- Derived Math Functions 205
- Section 9. Program Control 207
- CallTable 208
- Data, Read, Restore 209
- ClockSet 209
- Delay (Option, Delay, Units) 210
- FileManage 212
- FileMark (TableName) 213
- For ... Next Statement 213
- Power Off 217
- RunDLDFile 218
- Reset Table 219
- Select Case Statement 221
- Slow Sequence 223
- While…Wend 227
- This is a blank 236
Prodotti e manuali riguardandi Misurazione, test & controllo Campbell CR5000
(8 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale