Campbell CR510 Manuale dell'Operatore Pagina 195
- Pagina / 264
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
APPENDIX F. MODBUS ON THE CR10(X) AND CR510
F-3
The register data is returned as two bytes per
register and two registers per input location.
Response for example 2:
Hex
Slave address 11
Function 03
Byte Count 08
Data Hi (Register 40009) C0
Data Lo (Register 40009) 00
Data Hi (Register 40010) 44
Data Lo (Register 40010) 0A
Data Hi (Register 40011) 00
Data Lo (Register 40011) 00
Data Hi (Register 40012) 1F
Data Lo (Register 40012) 00
Error check (LRC or CRC) --
The contents of 40008 and 40009 are C0 00 44
0A hex or a value of 555.000 in input location 5.
Input location 6 = 0.
For complete documentation please refer to the
Modicon publication referenced above.
- CR510 DATALOGGER 1
- OPERATOR'S MANUAL 1
- WARRANTY AND ASSISTANCE 3
- TABLE OF CONTENTS 5
- DATA RETRIEVAL/COMMUNICATION 6
- PROGRAM EXAMPLES 6
- INSTRUCTIONS 7
- INSTALLATION 7
- APPENDICES 8
- FEATURES OF CR510 9
- This is a blank page 10
- SELECTED OPERATING DETAILS 11
- CAUTIONARY NOTES 12
- CR510 DATALOGGER OVERVIEW 13
- OV2. MEMORY AND PROGRAMMING 15
- CONCEPTS 15
- OV4. PROGRAMMING THE CR510 21
- CR510 OVERVIEW 30
- ARRAYS, AND MEMORY POINTERS 45
- 3.1 PARAMETER DATA TYPES 49
- 3.2 REPETITIONS 49
- 3.4 INDEXING INPUT LOCATIONS 49
- 3.5 VOLTAGE RANGE AND 50
- OVERRANGE DETECTION 50
- 3.6 OUTPUT PROCESSING 50
- PROGRAM CONTROL 51
- 3.8 PROGRAM CONTROL LOGICAL 52
- CONSTRUCTIONS 52
- 3.9 INSTRUCTION MEMORY AND 55
- EXECUTION TIME 55
- 3.10 ERROR CODES 59
- 4.1 ON-LINE DATA TRANSFER 61
- INSTRUCTION 96 61
- 4.4 STORAGE MODULE 64
- 5.1 TELECOMMUNICATIONS 67
- COMMANDS 67
- 6.1 PIN DESCRIPTION 71
- 6.2 ENABLING AND ADDRESSING 72
- PERIPHERALS 72
- 6.3 RING INTERRUPTS 73
- 6.6 SYNCHRONOUS DEVICE 74
- COMMUNICATION 74
- 6.7 MODEM/TERMINAL AND 75
- COMPUTER REQUIREMENTS 75
- 7.1 SINGLE ENDED VOLTAGE 79
- 107 TEMPERATURE PROBE 79
- 7.2 DIFFERENTIAL VOLTAGE 79
- MEASUREMENT 79
- 7.4 ANEMOMETER WITH 81
- PHOTOCHOPPER OUTPUT 81
- LONG LEADS 82
- FULL BRIDGE 86
- 7.12 NONLINEAR THERMISTOR IN 90
- HALF BRIDGE 90
- CR510 & AVW1 93
- 12 V or 5 V 94
- 7.14 4 TO 20 MA SENSOR USING 95
- CURS100 TERMINAL INPUT 95
- SYNCHED TO REAL TIME 99
- PORTS (RAIN GAGE) 99
- 8.5 CONVERTING 0-360 WIND 100
- DIRECTION OUTPUT TO 0-540 FOR 100
- STRIP CHART 100
- - SAVING DATA PRIOR TO EVENT 101
- zero yields 110
- SEQUENCE 145
- 13.2 SINGLE-ENDED AND 146
- DIFFERENTIAL VOLTAGE 146
- MEASUREMENTS 146
- LENGTH ON THE SIGNAL SETTLING 147
- 13.4 BRIDGE RESISTANCE 156
- 13.5 RESISTANCE MEASUREMENTS 160
- REQUIRING AC EXCITATION 160
- 13.6 CALIBRATION PROCESS 161
- 14.1 PROTECTION FROM THE 163
- ENVIRONMENT 163
- 14.2 POWER REQUIREMENTS 163
- SUPPLIES 164
- 12V ALKALINE BATTERY PACK 165
- DESI PAK 166
- 14.7 GROUNDING 168
- 14.8 TERMINAL STRIP 169
- FOR SWITCHING RELAYS 169
- 14.10 MAINTENANCE 171
- APPENDIX A. GLOSSARY 173
- B.1 TELECOMMUNICATIONS 177
- COMMAND WITH BINARY 177
- RESPONSES 177
- B.2 FINAL STORAGE FORMAT 179
- APPENDIX C. ASCII TABLE 183
- D.1 INTRODUCTION 185
- D.2 EXAMPLE PHONE CALLBACK 185
- PROGRAM BASED ON A CONDITION 185
- AND IT’S COMPUTER SETUP 186
- APPENDIX E 189
- E.4 REMOTE DATALOGGER 191
- PROGRAMMING 191
- F.1 TERMINOLOGY 193
- F.2 COMMUNICATIONS AND 193
- COMPATIBILITY 193
- F.3 MORE ON MODBUS 194
- AND CR23X MANUALS 199
- AD1 Major Differences 201
- AD3.1 Programming changes 202
- Section 12 205
- TABLE DATA ADDENDUM 206
- OV4. PROGRAMMING THE CR10X 207
- OV5. PROGRAMMING EXAMPLES 209
- 32 converts the 211
- 03:P84 Data Table Instruction 212
- OV6. DATA RETRIEVAL OPTIONS 213
- DATALOGGER 214
- COMPUTER 214
- SECTION 1. FUNCTIONAL MODES 215
- STATUS - ∗B 217
- 1.7 ∗C MODE -- SECURITY 217
- 1.8 ∗D MODE – TRANSFER 217
- PROGRAMS, GENERAL SETTINGS 217
- 1.9 *9 DATA TABLES SIZES 221
- 2.1 FINAL STORAGE AND DATA 223
- 2.2 DATA OUTPUT FORMAT AND 225
- RANGE LIMITS 225
- KEYBOARD/DISPLAY *7 MODE 225
- 8.1 COMPUTATION OF RUNNING 229
- 8.2 RAINFALL INTENSITY 230
- 8.3 USING CONTROL PORTS AND 231
- LOOP TO RUN AM416 MULTIPLEXER 231
- TO COUNT SWITCH CLOSURES 233
- (RAIN GAGE) 233
- 8.5 SDM-A04 ANALOG OUTPUT 234
- MULTIPLEXER TO STRIP CHART 234
- Section 12. Program Control 243
- Instructions 243
- Security 248
- Remote Location/Coil/Register 248
- Remote Location 249
- Local Location 249
- Send Message (P192) 250
- Message Type 251
- Number of Remotes 252
- First Remote Address 252
- Time into Transmit Interval 252
- Transmit Interval 252
- Swath to Receive 253
- Seconds Until Transmit (P194) 254
- Swath to Receive From Master 256
- Swath to Send 256
- First Location to Send 256
- Force Route (P197) 257
- Set Setting (P198) 257
- Result Location 258
- Beacon Intervals 259
- Neighbor Filter 260
- LIST OF TABLES 261
- LIST OF FIGURES 263
Prodotti e manuali riguardandi Misurazione, test & controllo Campbell CR510
(2 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale